PDD Case Study #2: with Feedback
0 of 20 Questions completed
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
0 of 20 Questions answered correctly
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Based on the building type, occupancy and zoning for this residential building project, how much taller than the current proposed height can the project be and remain within the maximum building height?
The Owner added a basement level, if the Total Budget is $1,501.400. What percentage of the total floor area is currently planned for the basement level?
Detail 5/A-6.19 specifies a washer at the connection between the microlam ledger and the anchor. What is the purpose of the washer?
The Contractor is working to give a preliminary cost estimate on the steel structure for this project. What size post is holding up the floor in the kitchen?
The Owner of this project is concerned about sustainability and wants an estimate of how much concrete will be used in the walls and foundation. In order to do this, you need to know the size of the footings. What is the width of the footing on the furthest east side of the garage?
The Architect is explaining the different meanings of the plumbing fixtures to the Owner. The plumbing fixtures are explanatory however, the Owner is concerned with the element name C.O., what’s the purpose of the element?
The FEMA floodplain requirements for the area that this project will be built in require that the FFE be a minimum of 8”. Considering the FFE is 0’ 0”, what is the FFE of the basement?
The Owner is requesting more information about the project finishes. These ICF walls are made of a recycled EPS foam and cement mixture, but the Owner wants to know what the external wall finish will be. (Choose the best answer)
During design, the Owner requests to have a large window over the sink in the kitchen that can be easy to clean and preferably inoperable. What type of window did the Architect recommended to install?
The Contractor on this project is concerned about cost and wants an estimate of how much total concrete will be used in the walls and foundation. In order to do this, you need to know the size of the footings. What is the width of the footing on the south side of the garage?
A sub-contractor being considered for the electrical Work on this project is requesting information about the electrical system for this house. They want to know specifically what type of circuit breaker will be run to the dumbwaiter.
The sub-contractor is putting together a preliminary budget for the Contractor of this residential dwelling. They are requesting information on the number of circuits and the total breaker amperage that will be used for basement subpanel “C.” (Enter your answer in this format. Example: 00,000)
The Contractor is reviewing clearances needed for installing the mechanical ductwork for the project. What is the dimension of the largest return air register in the basement?
The Contractor is having a meeting on-site with a supplier. They want to know what size supply line is providing water to the second-floor plumbing fixtures?
Where is the water heater located in this project, and is it propane or electric?
When installing a ledger in this type of ICF wall, according to the drawings, what size hole should be made in the foam to allow concrete to embed anchor bolts supporting the ledger?
According to the Construction Drawings for this residential project, what type of weld size is required for the W 16 X 40 beam
Detail 3/6.17 is a revision change in design during the Construction Documents, the Owner wanted the spandrel panel to extend to the parapet wall and to have a curtain wall on that side of the residence. The coping will need to be coordinated with the curtain wall supplier, what is a likely failure point on the assembly of the curtain wall? (select four)
The basement level exterior walls of this project will also be retaining earth, as the structure is partially underground. What is the minimum overlap of the rebar reinforcing used in the ICF walls in this area?
What’s customary meaning of the cloud on detail 3/ A-6.17 per documentation standards?